Overall it’s a good tool. Center is …
Overall it's a good tool. Center is accurate within +/- .002, the retracting pin retracts smoothly and the chuck offers better grip than the standard, came with the lathe, drive center.
A downside; when working with softer hardwoods like oak and hickory, etc, the drive center offers great bite. When working with very dense wood like african blackwood and mopani any excess above the normal amount of stress on the piece will cause the spur center to slip requiring you to remove the workpiece and brush the spurs to get a good bite back. Kind of annoying but not a deal breaker. If every other spur were removed I believe it would be an exceptional tool. Either way, my standard drive center is a permanent bench warmer.
Viviano also commented
Much of the challenge in wood turning is holding the wood. You can use a heavy center after cutting cross slots and a drilling a hole; 3 finger chucks to squeeze the wood; face plates after drilling holes. But if you want something quick to hold 1-2 inch stock with no preparation, this is it. I use it at least 50 percent of the time. Its spring loaded center and fine teeth allow me to mount wood quickly in about 30 seconds. The scar that it leaves is usually less than 1/32 inch. Best of all, I've never had it split the wood like my other centers.
I have used a Sorby and another similar model and I think this one is every bit as nice as the Sorby, biggest difference is the size of the "teeth", Sorby's are smaller. I don't think this difference affects usage.
In all honesty I was amazed when I opened the plastic case it comes in and saw it. The construction and fit and finish are extremely good.
Update 12/08:
We now have 2 of these at the facility where I teach as well and they have held up great. Many of my students are so pleased with them they end up buying them as well.
Recent comments by Viviano
I've recently purchased this lathe and was very happy with it when I first received it however the flimsy tailstock and tool rest screws quickly became stripped with just moderate amount of torque to them. This proxxon lathe could have been the ideal small scale lathe if the company didn't cheap out when it came to building the tool rest and the tailstock. I am going to call the company and get them to replace the tool rest and the tailstock and then I am going to put this tool on Ebay and get rid of it for the Taig lathe. You can buy the Taig with a turners set up for a small price and the components will last a lifetime. Proxxon would have had a great product if they had not gone cheap on the tailstock and the tool rest. I am going to buy the Taig and I'm sure I'll be happy with it. The Taig has many available accessories for it also and the Proxxon does not. I wish Proxxon had done a better job with the making of the lathe and with the making of accessories for it. You can get the Taig lathe at the Lee Valley site ( Canadian site ). The Taig lathe has many available accessories that can be ordered and I think I will be much happier with it. I give it 4 stars because it would have been a truly great small lathe if Proxxon had put a little bit of effort into the materials that went into the tailstock and tool rest.
Gary R.
Hitachi 321373 Miter Saw Crown Right Side Molding Support for C10FSH and C10FSB
The crown molding vice and stoppers from Hitachi are a "Don't Bother". They are flimsy and small only about 2 inches of support to hold the crown molding in place. It's extemly hard to make 2 cuts the same. If you want to cut your crown molding standing up there are better options.
Hitachi 321374 Miter Saw Crown Left Side Molding Support for C10FSH and C10FSB
See my review for part number 321434. This accesory does not work.
Hitachi 321374 Miter Saw Crown Left Side Molding Support for C10FSH and C10FSB
The right and left crown molding support worked great. One reviewer said it does not work at all. He must have an older version of the saw because it attached to my saw with no problem and it was easy to adjust. My only complaint is the cost. The same crown molding support for a Dewalt saw is half the price.
Woodstock W1001 6-1/2-Inch Jointer Flange
A great way to reduce the amount of saw dust you need to sweep up.
powered by SEO Super Comments
Tags: 1Inch, Center, crown, Drive, lathe, LCENTSS22, Super, with, wood, woodworking
I have used a Sorby and another similar model and I think this one is every bit as nice as the Sorby, biggest difference is the size of the “teeth”, Sorby’s are smaller. I don’t think this difference affects usage.
In all honesty I was amazed when I opened the plastic case it comes in and saw it. The construction and fit and finish are extremely good.
Update 12/08:
We now have 2 of these at the facility where I teach as well and they have held up great. Many of my students are so pleased with them they end up buying them as well.
Overall it’s a good tool. Center is accurate within +/- .002, the retracting pin retracts smoothly and the chuck offers better grip than the standard, came with the lathe, drive center.
A downside; when working with softer hardwoods like oak and hickory, etc, the drive center offers great bite. When working with very dense wood like african blackwood and mopani any excess above the normal amount of stress on the piece will cause the spur center to slip requiring you to remove the workpiece and brush the spurs to get a good bite back. Kind of annoying but not a deal breaker. If every other spur were removed I believe it would be an exceptional tool. Either way, my standard drive center is a permanent bench warmer.
Much of the challenge in wood turning is holding the wood. You can use a heavy center after cutting cross slots and a drilling a hole; 3 finger chucks to squeeze the wood; face plates after drilling holes. But if you want something quick to hold 1-2 inch stock with no preparation, this is it. I use it at least 50 percent of the time. Its spring loaded center and fine teeth allow me to mount wood quickly in about 30 seconds. The scar that it leaves is usually less than 1/32 inch. Best of all, I’ve never had it split the wood like my other centers.